Instalar Dovecot con postfix en CentOS

Install and configure Dovecot on CentOS

• Last updated on: 2018-10-29
• Authored by: Lee Jelley

If you have installed the Postfix mail server to operate as the Simple Mail Transfer Protocol (SMTP) service on an email server, you might still need a way to retrieve the incoming mail from the server.
This article shows you how to install and configure Dovecot, an open-source Internet Message Access Protocol (IMAP) and Post Office Protocol version 3 (POP3) server application designed specifically for Linux® and UNIX® operating systems. Dovecot retrieves emails from Postfix and delivers them to the relevant mailbox on the server.
You can get your mail through Dovecot by using either the POP3 or the IMAP protocol.

Prerequisites

You need the following operating system and software to use Dovecot:

• A CentOS® 6.0 or later Linux distribution
• Postfix

Install Dovecot

Download and install the Dovecot package by running the following command:

$ sudo yum install dovecot

Configure Dovecot

After you install Dovecot, you need to configure the services in the configuration file at /etc/dovecot/dovecot.conf. This example uses the nano text editor, but you can use any text editor that you want.

1. Use the following command to open the file in nano:
   

   $ sudo nano /etc/dovecot/dovecot.conf
   

2. Uncomment the following lines in the file and, if necessary, change them to reflect your plans for the environment:
   

   protocols = imap pop3
   mail_location =  maildir:~/Maildir
   

   These lines contain the following parameters:
   
   • protocols: The protocols through which users can access their email
   • mail_location: The format and the location of each user’s mailbox

Configure the authentication process file

Next you need to configure the authentication process file, which is located at /etc/dovecot/conf.d/10-auth.conf.

1. Use the following command to open the file in nano:
   

   $ sudo nano /etc/dovecot/conf.d/10-auth.conf
   

2. Uncomment the following line in the file and, if necessary, change them to reflect your plans for your environment:
   

   auth_mechanisms = plain login
   

   The auth_mechanisms parameter specifies the method that the email client uses to authenticate with Dovecot.
   

Configure the mail location

You can set the location for your mail by editing the configuration file at /etc/dovecot/conf.d/10-mail.conf.

1. Use the following command to open the file in nano:
   

   sudo nano /etc/dovecot/conf.d/10-mail.conf
   

2. Either add or uncomment the following line in the configuration file:
   

   mail_location = maildir:~/Maildir
   

Configure Postfix SMTP authentication

Next you need to configure the UNIX socket for Postfix SMTP authentication (SMTP AUTH). The file that you need to change is located at /etc/dovecot/conf.d/10-master.conf.

1. Use the following command to open the file in nano:
   

   sudo nano /etc/dovecot/conf.d/10-master.conf
   

2. Comment out the following lines:
   

    #unix_listener auth-userdb {
        #mode = 0600
        #user =
        #group =
      #}
   

3. In the same file, edit the following lines:
   

    # Postfix smtp-auth
      unix_listener /var/spool/postfix/private/auth {
        mode = 0666
        user = postfix
        group = postfix
      }
   

Configure POP3

Finally, configure the /etc/dovecot/conf.d/20-pop3.conf file, which enables older and less popular email clients to connect and transmit messages correctly.

1. Use the following command to open this file in nano:
   

   sudo nano /etc/dovecot/conf.d/20-pop3.conf
   

2. Uncomment or add the following lines:
   

   pop3_uidl_format = %08Xu%08Xv
   pop3_client_workarounds = outlook-no-nuls oe-ns-eoh
   

Create a mailbox

The example in this section adds a mailbox that a hypothetical user named Joe Bloggs (joe.bloggs) can use to send and receive emails.
You can create a user for this example, or you can use an existing user.

1. If necessary, use the following command to make a new user:
   

   sudo useradd joe.bloggs
   

2. Use the following command to create the mail directory for your user:
   

   sudo mkdir /home/joe.bloggs/Maildir
   

3. Give ownership of the mailbox that you just created to joe.bloggs by changing its permissions:
   

   sudo chown joe.bloggs:joe.bloggs /home/joe.bloggs/Maildir
   sudo chmod -R 700 /home/joe.bloggs/Maildir
   

Start Dovecot

Use the following steps to start the Dovecot service:

1. Use the following chkconfig command to verify that the Dovecot application will run when the server is restarted:
   

   sudo chkconfig --level 345 dovecot on
   

2. Use the following command to start the Dovecot service:
   

   sudo service dovecot start
   

Configure Postfix

Next, you need to configure Postfix to enable your email client to connect to your new SMTP server.

1. Use the following command to open the file at /etc/postfix/main.cf in nano:
   

   sudo nano /etc/postfix/main.cf
   

2. Add the following lines to the file:
   

    smtpd_sasl_auth_enable = yes
    smtpd_sasl_security_options = noanonymous
    smtpd_sasl_local_domain = $myhostname
    smtpd_recipient_restrictions = permit_sasl_authenticated,permit_mynetworks, reject_unauth_destination
    broken_sasl_auth_clients = yes
    smtpd_sasl_type = dovecot
    smtpd_sasl_path = private/auth
   

3. After you have added the preceding lines, exit the main.cf file and restart the Postfix service by using the following command:
   

   sudo service postfix restart
   

Add ports to iptables

Now that you have enabled secure SMTP Secure Sockets Layer (SSL), you should allow connections to port 587 by opening the port for your server in iptables.

1. Add the rule for this port by entering the following command:
   

   sudo iptables -I INPUT 2 -p tcp --dport 587 -j ACCEPT
   

2. Add the POP and IMAP ports, as well as their secure counterparts:
   

   sudo iptables -I INPUT 3 -p tcp --dport 110 -j ACCEPT
   sudo iptables -I INPUT 4 -p tcp --dport 143 -j ACCEPT
   sudo iptables -I INPUT 5 -p tcp --dport 993 -j ACCEPT
   sudo iptables -I INPUT 6 -p tcp --dport 995 -j ACCEPT
   

3. Use the following commands to save the iptables rules and restart iptables:
   

   sudo /etc/init.d/iptables save    sudo /etc/init.d/iptables restart
   

Fuente: https://support.rackspace.com/how-to/dovecot-installation-and-configuration-on-centos/